INERT PRODUCTS, IED TRAINING, EXPLOSIVE DEVICES FOR MILITARY, POLICE, LAW ENFORCEMENT, CUSTOMS, SECURITY AGENCIES - NOT AVAILABLE FOR THE GENERAL PUBLIC - LIFETIME GUARANTEE ON ALL PRODUCTS
Home > Circuit Boards and Sensor/Initiator Circuitry > LIGHT LEVEL FALLING - LIGHT SENSITIVE IED

LIGHT LEVEL FALLING - LIGHT SENSITIVE IED

LIGHT LEVEL FALLING - LIGHT SENSITIVE IED

LIGHT LEVEL FALLING - LIGHT SENSITIVE IED
Training models ITA-110 (light level rising) and ITA-111 (light level falling) are built around very similar circuitry. In ITA-111 the sensor and electronic circuitry are almost identical to the setup in ITA-110. The circuitry is designed to close the relay contacts when the light level on the sensor surface drops below a preset intensity threshold. In all other respects, the description for ITA-110 applies similarly to ITA-111.

These circuits use similar circuit and operate on a photo resistor sensor that detects light level. The circuit boards each have an adjustment. The variable resistor on the circuit boards allows for the instructor to pre-set the level at which the ITA-110 circuit will trigger a relay and detonator when the sensor is exposed to a light level higher than preset; the ITA-111 circuit board will trigger the closure of relay contacts when the sensor detects light level exposure to less than the preset light level setting.

Both circuit boards also contain an adjustable time reset feature allowing the instructor to set a delay ranging from 1 second up to 15 seconds, before automatically resetting to standby mode, awaiting the next change in light level for classroom demonstration.

Both circuit boards can be activated and demonstrated by the instructor, by shining a light on the sensor or taking the light away, or shutting off the room lights or opening a curtain or blind. The photo resistor senses the light level change and its resistance changes accordingly. The circuitry interprets this change in electrical resistance and operates the relay contacts. A separate power source is wired through the relay contacts, and to an inert detonator containing and LED, for visual indication of electrical continuity, and to a small piezo whistle for an audible indication of continuity. These two indicators simulate “detonation”.

In ITA-111, the circuitry is designed so that it triggers when the circuit board (and improvised explosive device) are moved from a location where the light is bright, to an area of reduced or subdued light, shadow or darkness. The light level drop can be set using the two sensitivity settings. They have been factory set for normal room light at our location but may have to be reset by you. It is recommended that you make a sketch of the adjusting screw slot position on each of the two potentiometers (variable resistors) before any adjustment is made. Otherwise, you may have trouble returning to the factory setting.

Turning off the lights, saving the training aid from bright light to shadow, or passing your hand over the sensor surface to reduce the intensity of light falling on it, will close the relay contacts and trigger the LED in the detonator.

The POWER toggle switch and the ARM-SAFE toggle switch should be shutoff and set to safe before connecting the batteries into the circuit.

Remove both batteries from the circuits by unsnapping the terminal strips, for storage or transport.

Use only a fully charged battery in each part of the circuit, or operation may be unreliable or unpredictable. We recommend alkaline batteries be used. If you have a battery tester or a volt meter, batteries should test at 8.75- 9.5 volts. At lower than 8.75 volts, the circuitry may not function.
Details
Order Sku ITA-111
 
Price: $225.00
Options
Quantity
: *
: *
: *
 
Inert Electronic Clock/Radio IED with Alarm Function
Inert Electronic Clock/Radio IED with Alarm Function
Clock radio. Device will initiate upon alarm functioning or radio being turned on. Note: After rewiring, unit will not meet U-L or CSA standards...
Order Sku: ITA-156
Price: Request quote
VIDEOCASSETTE CASE “GUN” BOOBYTRAP
VIDEOCASSETTE CASE “GUN” BOOBYTRAP
Videocassette Case “gun” boobytrap. Carefully modified to show no signs of tampering. Videocassette case IED with Anti Open Single Elastic Band...
Order Sku: ITA-165-B
Price: Request quote
SAFETY FUSE, INERT AS USED WITH NON-ELECTRIC DETONATORS OR FUSE CAPS
SAFETY FUSE, INERT AS USED WITH NON-ELECTRIC DETONATORS OR FUSE CAPS
Safety fuse, inert as used with non-electric detonators or fuse caps. Various colors. Sold by the 12 inch (25cm) length. Black, white, orange, and...
Order Sku: ITA-3
Price: Request quote
ELECTRIC HAIRDRYER IED
ELECTRIC HAIRDRYER IED
Electric Hairdryer IED
Order Sku: ITA-302
Price: Request quote
INERT BOOBYTRAP DOOR OPENING INITIATED CLOTHESPIN SWITCH
INERT BOOBYTRAP DOOR OPENING INITIATED CLOTHESPIN SWITCH
Clothespin switch/door device is set to initiate when door is opened.
One part of the device attaches to the door frame, and the other part...
Order Sku: ITA-36
Price: Request quote
INERT BOOBYTRAPPED CACHE GOODS IED
INERT BOOBYTRAPPED CACHE GOODS IED
CACHE -A-. Based on principle of explosive hidden inside cache goods that are piled up. When the items are moved or lifted the I.E.D. inside the...
Order Sku: ITA-39
Price: Request quote
INERT TRIPWIRE IED BUILD INTO BAMBOO POLE
INERT TRIPWIRE IED BUILD INTO BAMBOO POLE
Bamboo pole. Built into a large diameter bamboo pole. Typical Viet-Cong device, Tripwire initiated.
Order Sku: ITA-46
Price: Request quote
MILITARY AND IMPROVISED BOOBYTRAPS
MILITARY AND IMPROVISED BOOBYTRAPS
Military and improvised Boobytraps: Four US issue boobytraps. Improvised boobytraps: pressure, tilt (ball-in-tube), photo-electric, trip...
Order Sku: ITA-623
Price: Request quote
SUSPENDED DEVICE WITH CLOTHES PIN INITIATOR
SUSPENDED DEVICE WITH CLOTHES PIN INITIATOR
Suspended device with clothes pin initiator.
Order Sku: ITA-64
Price: Request quote
IMPROVISED TREMBLER
IMPROVISED TREMBLER
Improvised trembler. Device contains an improvised trembler (vibratory) switch. An extremely dangerous switch because of its potential for great...
Order Sku: ITA-77
Price: Request quote
CLOCKWORK INDICATING FUSE
CLOCKWORK INDICATING FUSE
Clockwork indicating fuse, an indicating fuse is a power limited device which cuts the flow of electricity when overloaded. It contains a spring...
Order Sku: ITA-92
Price: Request quote
INSTIGATED CHEMICAL (HYPERGOLIC) REACTION IED MODEL
INSTIGATED CHEMICAL (HYPERGOLIC) REACTION IED MODEL
Instigated chemical (hypergolic) reaction IED model
Order Sku: ITA-BC-1-21
Price: Request quote
Printable version

Product Categories

Product Site Map

Your Cart

Cart is empty

Info Links

Bestsellers